General

•Improved areas in 3DCS to support more characters, such as in DOE Viewer. (75580)

GeoFactor

•Show Min/Show Max, within the GeoFactor Analysis Tab, will show the GeoFactor's Min(WC) or Max(WC) on screen and the value in the measure. (76001)

Contributor Analysis

•Resolved an issue in Mean Shift where the displayed value was incorrect when contributors were shown per feature. (76200)

•Updated the Sensitivity Analysis to display part names consistent with the tree view, respecting Alias Name settings. (76157)

•Fixed an issue where the Best Fit move floats was not allowing Contributor Analysis to finish running. (75981)

Critical Tolerance Identifier

•Fixed an issue with Critical Tolerance Identifier (CTI), when showing Pp%, to show the correct values to equal 100%, whether the model is set to show in MM or Inches. (76064)

GD&T

•Updated how Dimensioning Location and Form tolerances interact. Form will act as a refinement to Dimensioning Location. (75715)

•Resolved an issue where position GD&T did not produce truncated results as expected. (76269)

•Resolved an issue in the dimension distance measurement where minimum and maximum values were not calculated or displayed correctly. (76068)

•Fixed how Auto Refine on Slot/Tabs will correctly affect the Monte Carlo results. (76102)

•Removed DRF requirement and validation message for MMB/LMB on Pattern of Hole/Pin features. (76010)

•Changed how AutoRefine behaves when when Orientation is equal to Form, or when Form is larger than Orientation. (75813)

oIf Orientation and Form are equal values, all of Form will be applied as the refinement.

oIf Form is larger than Orientation, selecting OK will show a warning that Form can only be equal or lower than Orientation.

Moves

•The Autobend Move will correctly display the Move direction. (75935)

•Fixed an issue with switching an invalid Float to a valid Float within a move which was displaying the wrong warning messages. (75901)

•Enhanced Feature Move functionality to support Torus-type features. These are now interpreted as axes rather than points within 3DCS. (75719)

•The Transform move will now allow to select a center point to rotate parts. (75941)

Tolerance

•Added an option to the Capability Tolerance to run Sigma Range or Min/Max Range. Fixed an issue when applying the Associated Direction measure to apply the deviation along the associated direction. (75833)

•Fixed the tolerance dialog to display the vector direction correctly for multiple points. (75905)

•Fixed an issue with mixed features (Slots and points) where the point variation was not shown in Sensitivity. (75708). 

Measures

•Fixed an issue were applying multiple GD&T Measures to a single feature caused incorrect behavior when canceling. When two or more GD&T Measures were applied to the same feature, clicking Cancel or the X button would incorrectly copy details (such as Name, DRF, etc.) from the first measure. (76230)

•Corrected the order GD&T Measures are shown in the Analysis Table View. The GD&T Measures would be show at the bottom of the list, rather than listed with the other measures. The measures will match the Model Navigator order. (76230)

•Restored Direction 2 in Point-to-Line Measure dialog for Projected on Plane mode. (76177)

•Improved the Virtual Clearance Measure to measure hole/slot pairs. (75922)

Dialog

•Added Center Tree and Reframe On to the right-click menu in the Auto-Point Projection dialog. (75752)

•Fixed a bug in GeoFactor Analyzer results was changing when running a second time. (75900)

•Fixed a bug in Measure Generator dialog to show the correct name in the warning message of the feature pair that is removed. (75745)

•Fixed a bug in Measure Generator dialog to rearrange the features correctly when a feature pair is removed from the list. (75745)

•Corrected the display values for Rand#2 and Rand#4 within the Circle Tolerance. In 3DCS, displaying values as Plus/Minus or Upper/Lower would show the total range, but the software then adjusts the range to represent half the tolerance—resulting in an incorrect display value. (75841)

•Fixed an issue with the Summary in the Analysis Summary window. This function will correctly create and open the HTML Summary of the Analysis. (75849)

Validate

•Added a Validation message for Symmetry, when applied on a Hole/Pin feature. "Invalid Feature Type - Symmetry requires a Slot or a Tab." (75486)

Reporting

• APQP Report:

oUpdated to exclude inactive moves. (76112)

oResolved an issue where images failed to generate for Moves with names containing special characters. (76075)

oResolved an issue where images for moves involving a single part were not being generated correctly. (75684)

•Fixed an issue with the DFMEA section in the HTML report and addressed misalignment in the Contributor columns. (75979)

•Fixed an issue in the Geofactor Analyzer results window were it was not displaying the correct sort by type after Generating the Report. (75792)

NX useful topics: See more topics on Best Practices and FAQ on the DCS Community.

•General Information

•Creating GD&T with PMI

•3DCS and Teamcenter Configuration - Learn how to setup 3DCS to save all data into Teamcenter.

Dialog

•Resolved an issue when deleting an item in the Model Navigator could inadvertently remove the associated part. This behavior has been corrected—3DCS now prevents part deletion directly from the Model Navigator, ensuring model integrity is maintained. (74870)

•Users can select either a Point Group or a Point list to convert the list of points to the CAD system. (72468)

Extract GD&T

•Fixed an issue when extracting a Radius size tolerance, which would incorrectly double the range. (75918)

CATIA V5 useful topics: See more topics on Best Practices and FAQ on the DCS Community.

•General Information

•Creating GD&T with FT&A.

General

•Resolved an issue where points and labels were visible during move creation or editing, despite being set to hidden. (75967)

•Resolved an issue where Features highlight not refreshing from the Feature Linking Wizard. (75882)

•Fixed a crash when using Excel Export. (75482)

Dialog

•Users can select either a Point Group or a Point list to convert the list of points to the CAD system. (72468)

Extract GD&T

•Fixed an issue when extracting a Radius size tolerance, which would incorrectly double the range. (75918)

Spec Study

•Fixed an issue with Influence Sphere in Spec Study not showing the sphere after selecting Show Item. (75913)